VNC viewer session with gnome session manager on Ubuntu 11.10

The following happens to me since I upgrade my Ubuntu to version 11.10.

Using the default config file .vnc/xstartup, I just get a terminal window in my VNC viewer session.


To have the gnome desktop session manager back to the VNC viewer session, I have to modify the config file as follows.

#!/bin/sh

# Uncomment the following two lines for normal desktop:
unset SESSION_MANAGER
unset DBUS_SESSION_BUS_ADDRESS
#exec /etc/X11/xinit/xinitrc

[ -x /etc/vnc/xstartup ] && exec /etc/vnc/xstartup
[ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources
xsetroot -solid grey
vncconfig -iconic &
x-terminal-emulator -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" &
#x-window-manager &
gnome-session --session=gnome-classic &


In the following, the value after --session= is the session manager. You may change gnome-classic above to ubuntu-2d for an alternative session manager.

Comments

  1. JAug 2, 2012, 10:46:00 AM

    Changing gnome-classic to ubuntu-2d does not work. I get a "Failed to load session ubuntu-2d" message. Any ideas?

    ReplyDelete
    Replies
    1. Eddie LauApr 13, 2013, 5:33:00 PM

      You may do the following command to make sure that unity-2d (which ubuntu-2d wants to start) has been installed on your system.

      sudo apt-get install unity-2d

      Delete
  2. vikasJul 19, 2013, 11:47:00 AM

    i am trying to use vnc on ubuntu 13.04 but I am unable to get vnc working. It says ""Failed to load session ubuntu-2d". I have the xstartup file same as you mentioned. Any ideas how to solve this?

    ReplyDelete
    Replies
    1. Eddie LauAug 4, 2013, 10:56:00 AM

      According to this thread (http://askubuntu.com/questions/247501/i-get-failed-to-load-session-ubuntu-2d-when-using-xrdp), ubuntu-2d is no longer available. You may wish to switch to some other session manager.

      Delete

Post a Comment

Popular posts from this blog

Using PlayStation 1 Densha de Go controller on emulators

Image
Items needed Arduino Leonardo (or equivalent). Note that it has to have at least one 3.3V power output. A standard PlayStation 1 controller A Densha de Go controller 6 male-to-female jumper cables Procedure Initial Cabling Using the jumper cable, connect the typical PlayStation 1 controller with the Arduino Leonardo. PlayStation 1 controller pin numbers --------------------- \ 1 2 3 4 5 6 7 8 9 /  ------------------- Connection to Arduino Leonardo * PlayStation 1 controller pin 1 (DATA) --> Arduino Leonardo digital port 12  * PlayStation 1 controller pin 2 (CMD) --> Arduino Leonardo digital port 11  * PlayStation 1 controller pin 4 (GND) --> Arduino Leonardo port GND  * PlayStation 1 controller pin 5 (VCC) --> Arduino Leonardo port 3.3V  * PlayStation 1 controller pin 6 (ATT) --> Arduino Leonardo digital port 5  * PlayStation 1 controller pin 7 (CLK) --> Arduino Leonardo digital port 4 Set up Arduino IDE Install the IDE is available at  https://www.arduino.
Read more

Using PS1/PC Densha de Go! controller SLPH-00051/TCPP-20001/DGOC-44U on PS4/Switch Densha de Go!!

Image
Items needed A Densha de Go! controller (PS1 original version SLPH-00051, the one-handle version TCPP-20001, or the USB PC version DGOC-44U) A Titan Two A few micro USB cables A PlayStation 4 with controller/A Nintendo Switch with a USB controller A PlayStation 4/Nintendo Switch Densha de GO!! game [Required for SLPH-00051 and TCPP-20001 only]: Either Arduino Leonardo (or equivalent). Note that it has to have at least one 3.3V power output 6 male-to-female jumper cables or a  Mayflash SS/N64/PS2 Controller Adapter for PC USB  (which has issue setting P0 and P4 correctly if the player switches between these two states quickly) Adding a USB interface for the PS1 Densha de Go! controller Do this if you are using PS1 Densha de Go! controller. Arduino approach Cabling Using the jumper cable, connect the Densha de Go! controller with the Arduino Leonardo. PlayStation 1 controller pin numbers --------------------- \ 1 2 3 4 5 6 7 8 9 /  ------------------- Connection to Arduino Leonardo * Pla
Read more

Play octoshape stream on windows with VLC player

Install windows octoshape plugin at http://www.octoshape.com/files/octosetup.exe Install VLC player at http://www.videolan.org/vlc/download-windows.html . Use the installer so later octoshape can pick it as the preferred player. (Updated 12/26/2010: A dirty way to make sure windows associate all media files to vlc player is to explicitly set in vlc's Tool -> Preferences -> Interface -> Set up associations, select all file types. Then in Octoshape Settings (right click on the Octoshape system tray icon and select Settings), select use "System player") Create a bat file named stream.bat. In Windows XP, type in the bat file. "C:\Documents and Settings\ [user]\Application Data\Octoshape\Octoshape Streaming Services\OctoshapeClient.exe" -url:[octostream] In Windows Vista/7 "C:\Users\[user] \AppData\Roaming\Octoshape\Octoshape Streaming Services\OctoshapeClient.exe" -url:[octostream] Replace [user] with your current user name, [octostream] w
Read more